The former might be as a result of the latter but I am stumped. Install a driver providing OpenGL 2.0 or higher”. I get an error message from Radeon Software.you can just make out the icons but nothing more. The windows 10 taskbar is transparent i.e.Now when I start boot camp as a VM in Fusion under MAC, I get video and the VM is again useable, however I have two issues:. On reboot everything seems fine when running Windows 10 native. On first boot the screen broke up into horizontal jagged lines forcing me to do a hard reboot. I therefore downloaded and installed the appropriate driver from the AMD website. I therefore booted directly into Windows 10 and upgraded to November 21H2 build but noticed that it was running on Windows 10 default Video adapter driver! As I never installed Bootcamp I have never checked this before but although the right click context menu had AMD references, the driver itself was not installed. vmx! The VMware Knowledge base refers to the boot.ini file but I followed the advice on this forum and deleted and the recreated the Bootcamp VM.This worked but I then had a black screen with a cursor although I could see from disk activity they the VM was running. I was aware that 8.5 was not compatible with Catalina so have installed Fusion Player 12.0.Īll of my VMs upgraded and worked fine in Fusion Player except Bootcamp. I have had to bit the bullet and upgrade to Catalina due to software issues such as Office 2016 for Mac going end of life, and I needed to install Office 365. Apart from a few issues with Windows 10 activation when switching between a Virtual Machine and booting directly into windows its been pretty stable. Check that the virtual machine's firewall is not blocking Internet access. Right-click the local area network connection, and select Enable. Click Start > Control Panel > Network Connections. I have been running my VMs using VMware Fusion 8.5 on a late 2015 27” iMac running Sierra.įusion 8.5 was pre-installed as was Windows 10 Bootcamp. Check the VMware host has correct network connection. Start An圜onnect and bring the tunnel up.I wonder if anyone can give me some help and guidance on the following issues.Launch your Fusion VM, post the result of netstat -rn.Restart the computer, post the result of netstat -rn.To confirm the above is correct, do the following: I expect then that everything will work swimmingly, and you will also have access to your (printer? or other devices) to boot! You could for example make your home network 172.16.0.0/24, and your NATted VPN network 172.16.1.0/24. Possible solution: move your local subnet to something outside the ranges captured by that split tunnel. Cisco does a terrible job of cleaning up routes when the An圜onnect client is quit. Since this range is captured by the VPN tunnel, the traffic is instead routed over the tunnel.Īs for why this behavior persists even after the tunnel is torn down, and the An圜onnect client has been quit. However Fusion has to set up a routing rule on your machine that says that traffic bound for 172.16.249.128 needs to be NATted to your local IP in the 10.0.0.0/24. Since the 172.16.249.128 that Fusion is using for your VM falls inside the 172.16.0.0/12 network space identified by RFC-1918 one would expect that it is not going to be affected by your VPN tunnel. You can check this by activating the VPN and attempting to access something else on your network (printer maybe?) I expect the connection will fail. If your local network is 10.0.0.0/24, it would seem the Cisco VPN is capturing this, and routing all outgoing traffic over the tunnel ( 10.0.0.0/8 includes 10.0.0.0/24) When the VPN tunnel is up, all traffic from your Mac bound for your local network ought to go over the VPN tunnel. Of course all this was working before Apple changed to NetworkExtension framework. I've ready a bunch of fusion community posts that have similar issues, but they have all been patched as of fusion 12.2.3, afaik. They have advised it's setup for split tunneling: 10.0.0.0/8, 194.xx.xx.0/21, some ranges in 192.168.0.0 -> tunnel, Anything else -> to default route (normally internet) The Cisco config is supplied by our company IT. Restarting Fusion's services doesn't work and I end up having to reboot the mac. What's worse is after disconnecting the the VPN, I still can't access the VM. From inside the VM I can access the WAN but nothing from the VPN. However as soon as I connect the VPN, I loose access to the VM. With the VPN not connected, I can access services from the host to the guest. The VM is network is set to "Share with my mac" NAT and is on DHCP. The VPN is Cisco An圜onnect Secure Mobility Client 3. I'm on Mac OS 11.6.5 Big Sur running a Windows 2019 Server guest from VM Ware fusion 12.2.3.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |